What is the difference between the internal hub and derailleur?The derailleur offers a much larger gear range than an internal hub. This can help the bike run more efficiently as well as give it more low-end torque, and high-end speed. The internal hub is for those who go through some rough terrain, such as mud, fields, tall grass. Not having a derailleur allows this bike to go through all of this without any worry of a derailleur getting broken off. The internal hub is geared fairly low to make climbing easier but loses a little torque and some top end going from 11-speeds to only 3.
What tire pressure should I use?This is more of a personal preference rather than a set in stone range. We recommend 15-20 psi if on pavement and 10-15 psi if off-road and 8-10 psi if you are in very soft conditions like snow or sand. Which tire pressure works best for you also depends on rider weight and if you are pulling a trailer. These ranges are just general guidelines. Disclaimer: Our bikes have tubes in the wheels and the lower the air pressure you run the more susceptible you are to getting flats due to the tube pinching.
What is the top speed of a rambo bike?The top speed of all of our R750 and R750XP bikes is governed at 19mph and may or may not be able to reach that speed depending on rider weight including any cargo. The top speed of our R1000XP varies as well on rider weight and cargo, but tops out between 26 and 30mph.
I have an internal hub and it has this clicking. Is this normal/how can I get rid of it?
Yes, this clicking is due to the multiple clutches in the hub that engage the different gears. The only way for it to be completely silent is when the bike is under a load in first gear. Otherwise, there is no way to get rid of the clicking.
Walk assist mode
If your bike is equipped with walk assist mode, Press and hold the “-” button on the handle bar control until “P” appears on the screen. The bike will begin to assist you 2-3mph and will stop assisting when you remove pressure from the “-” button
Most commonly this is caused when the silver magnet attached to a spoke on the rear wheel is no longer alined with the sensor that is attached to the frame. There are two types of sensors: Bolt-on or Zip-tied.
Bolt-on- For the magnet to be in the correct position on the bolt-on style, the magnet needs to pass by the center of the Bafang logo on the sensor.
Zip-tied- For the magnet to be in the correct position on the zip-tie mount style, the magnet needs to pass by the center of the sensor body where there is a raised circle.
If the magnet is in the correct position and you are still getting the error code, the next thing to check is that the sensor cable is still plugged in between the rear wheel and motor. When doing this also check to see if there is any damage to the cable. If the plug is still firmly attached and the cable appears to be in good condition then something has become faulty in the sensor and the only remedy is by contacting Rambo for a replacement.
I have the 3 speed hub and my wheel no longer turns when I pedal or use the throttle, but the chain moves like it should
This is generally caused by too much force being put on to the rear chain gear(sprocket) on the rear wheel. This sprocket engages the hub with 3 splines that have likely sheared off. Your bike will need a replacement sprocket. (RP-14-03-01)
I have the 3 speed hub and I have received and installed the warranty chain and sprocket, and now i am getting error 21 and/or my rear brake won't adjust or engage properly
For the error 21, have the customer align the magnet on the rear wheel with the sensor on the left side of the frame. Make sure magnetic side is facing the sensor. For the issue of the brake no longer being aligned, this is caused by the chain not being sized to the bike. The warranty chain that is sent out is a universal size and is one link too long. One link must be removed from the chain before install for it to properly fit on the bike. Once one link is removed the wheel will sit in a similar position to how it originally was and the brake should only need minor adjustment if any.
My rear hub skips
This is generally caused by improper gear adjustment. Put the bike in third gear and tighten up the tension of the shifter so it is taut. To know if it is adjusted correctly, first gear should not click as you are pedaling. If this does not work, the Sheldon Brown website has another way of adjusting the shifting that tends to be a little more exact, but tedious. Here is the link: https://www.sheldonbrown.com/sturmey-archer_tech.html
Why does my bike click even when pedaling or using the throttle?
External Gears: Bikes that have a standard external gearing system should not click unless you are coasting and not pedaling.
Internal Gear Hubs: It is normal for internal geared hubs to click even when pedaling forward. This is because unlike external gears where there is only one clutch system with spring loaded pawls, (The things that make the clicking noise), there is a separate clutch for each internal gear. For example if you are in second gear and pedaling, your first and third gear are not engaged and therefor their pawls will be clicking.
One added piece of info: The hub may be silent when pedaling forward for the first couple miles or the first one hundred miles. This is caused by excess grease getting in to the clutch system during the manufacturing process. It is NOT recommended to take the hub apart.
What air pressure should i have my front suspension set at?
Some of the forks on our bikes come with a guide that is stuck onto one of the legs of the fork. If your bike doesn’t have a sticker there are two ways you can set the air pressure. It all comes down to personal preference, but also making sure you don’t bottom out the shock if you hit a bike hole, rut, etc.
The first way is setting the pressure of the fork to 100psi and riding to essentially guess and check to see if that pressure works for you. If it is too stiff or too loose for your preference add or remove air at 5psi increments until you reach the desired softness or firmness.
The second way is by using the band that is wrapped around the post that goes into the lower part of the fork as a guide, (you can use a zip-tie around that post instead if your fork didn’t have a rubber ring or it fell off).
Using something to lean on or a friend to hold up the bike, get on the bike and get into an “attack” position. This is done by standing up on the pedals and having your hands on the bars. Bounce up and down a few times to get the fork into resting position. After bouncing slide the rubber ring or zip-tie down to where the post feeds into the lower part of the fork. Gently get off the bike to try not to move the ring. When off the bike check to see if resting position is when 20-30% of your fork’s travel is used. If so you have the correct pressure. If not, add more air if resting position is 30% or more of your travel, or remove air if resting position is 20% or less of your fork’s travel. A general rule of thumb is to adjust by increments of 5-10 psi since it doesn’t take much to get into a good position.
Hub-drive vs mid-drive
Long story short, mid-drive motors provide more torque, which is what will help you get up hills and through the woods better. Hub drives are good for people that are using the bike as a form of transportation such as commuting on pavement or hard packed trails. Off-road is where the mid-drive motors excel, especially when paired with the power that Bafang offers that other competing mid-drives do not. That is why our moto is “takes you places you’ve never been!”
What e-bike class are rambo bikes considered?
Both R750 and R750XP models are considered class 2 E-Bikes while the R1000XP is considered a class 3.
What is the pedal assist range of a rambo?
A pedal assist range varies on many factors, the biggest ones are: rider weight, how technical or hilly the terrain is, what assist level you are on, and how much you are pedaling along with the assist. The effective pedal assist range after weighing in these factors is estimated somewhere around 10-30+ miles. 10 being high assist and/or hilly terrain, and 30+ being low assist level on relatively flat ground.
How long does it take to charge one of the batteries?
The batteries generally take 4-5 hours to charge when empty.
My charger sparks when I plug in my battery, is that normal?
The charger will spark when it is being plugged into the battery if it is not plugged into the wall outlet. When it is plugged into a wall outlet the charger is grounded and will prevent the spark.
Do rambo bikes charge as you pedal or brake?
No, there is no current technology to allow you to recharge that big of a battery through pedaling. You wouldn’t be able to generate enough power for it to recharge efficiently.
My bike does not turn on and the battery will not take a charge. How can I fix this?
This usually happens around early spring and Turkey Season. To figure out what happened you need to ask some questions. “When was the last time you used the bike?” If they say a few months ago, the battery was probably stored at a low charge and went into a “safety mode.” They will either need a replacement battery or try a jumpstart method. You can also recommend FTH Power which is a lithium ion battery refurbishing company in CA. If they say it was working fine the other day then have them test the charger with a voltmeter to make sure it is not the charger.